Matweb
We produce ASTM/ASME Grade 304, Grade 304L,304h, 316, 316L, 316H, 316TI, 321, 321H, 309S, 309H, 310S, 310H, 410S, 2205, 904L, 2507, 254, gh3030, 625, 253MA, S30815, 317L, Type 317, 316lN, 8020, 800, 800H, C276, S32304 and others special requirement stainless steel grade.
I consulted with a few materials engineers I know and obtained the response that until a numeric value is listed, there isn’t any minimal or maximum to the element. The factor is proven because a single desk is getting used for a variety of totally different grades and a number of the grades have that element controlled so there must be a column for it. For other grades, the place the component is “unspecified” no numeric worth is listed.
We also ask that you just discuss with MatWeb’s disclaimer and phrases of use relating to this data. Some of the values displayed above might have been converted from their original models and/or rounded so as to display the information in a consistent format. We additionally ask that you simply check with MatWeb’s terms of use concerning this information.
The composition percentage features a notice B that reflects the worth is the maximum until otherwise indicated. This would counsel that any copper is out of specification for ASTM A 312 kind 316L. See comments on this and another submit about ASTM A 941, Steel Alloy Terminology. On request we are able to produce material with a tensile power of over one thousand MPa .
Click here to view all of the property values for this datasheet as they were originally entered into MatWeb. I am not sure of this, however the copper presence might be an issue for corrosion resistance, as copper is extra energetic, from a galvanic viewpoint, than SS 316L . Therefore, A4-eighty is an austenitic, acid proof stainless grade (usually 316 materials – 316 or 316L) which has been cold worked to provide a minimum tensile power of 800N/mm² . Results are displayed up to a maximum of 200 materials per web page. Follow the hyperlinks under to view complete property data.
- The low carbon content decreases carbide precipitation that sensitizes the grain boundaries of welds in these materials.
- The supplied values tend towards the conservative end of the spectrum and could be used as baseline design values for preliminary design.
- Alloy 316/316L is molybdenum-bearing austenitic chrome steel.
- The materials property data offered are intended to be consultant of the fabric described.
- 1.4435 / AISI 316 L is an austenitic chromium-nickel-molybdenum stainless-steel with low carbon content material.
Stock Thickness: 0.1-200.0mm
Production thickness: 0.5.0-200mm
Width: 600-3900mm
Length: 1000-12000mm
Grade:
200 series: 201,202
300 series: 301,304,304L,304H,309,309S,310S,316L,316Ti,321,321H,330
400 series: 409,409l,410,420J1,420J2,430,436,439,440A/B/C
Duplex: 329,2205,2507,904L,2304
Surface: No.1,1D,2D,2B,NO.4/4K/hairline,satin,6k,BA,mirror/8K
Brand��Chanson,TISCO,BAOSTEEL,POSCO,JISCO,LISCO
If your material isn’t listed, please refer to our search assist web page for help in limiting your search. The search phrase you entered, 316l, is common to 60 supplies, by looking on the term [ “316l” ] in commonest textual content fields, .
We have thousands tons stock of stainless steel sheet and coil with various size and grade,mainly include austenitic stainless steel, martens stainless steel (including precipitation hardened stainless steel sheet & coil), ferritic stainless steel, and duplex stainless steel.
Characteristics of Stainless Steel Sheet and Plate:
High corrosion resistance
High strength
High toughness and impact resistance
Temperature resistance
High workability, including machining, stamping, fabricating and welding
Smooth surface finish that can be easily clean
flexible chrome steel gasoline line
Similar to Type 316 for superior corrosion resistance, but also has superior resistance to intergranular corrosion following welding or stress relieving. Good corrosion resistance to most chemical substances, salts, and acids and molybdenum content material helps resistance to marine environments. The low carbon content material of 316L reduces the potential for in vivo corrosion for medical implant use. 316L has fabrication characteristics just like Types 302 and 304.
Stock Thickness: 0.1-200.0mm
Production thickness: 0.5.0-200mm
Width: 600-3900mm
Length: 1000-12000mm
Grade:
200 series: 201,202
300 series: 301,304,304L,304H,309,309S,310S,316L,316Ti,321,321H,330
400 series: 409,409l,410,420J1,420J2,430,436,439,440A/B/C
Duplex: 329,2205,2507,904L,2304
Surface: No.1,1D,2D,2B,NO.4/4K/hairline,satin,6k,BA,mirror/8K